2
fillet
Started by ginevra, Feb 14 2020 01:24 PM
11 replies to this topic
#1
Posted 14 February 2020 - 01:24 PM
Hi you all,
I have a problem with the fillet command. Very often it doesn't work because "lines are not complanar". But if I see on the properties, both are on the same level. I also never draw in other plan than 2d. So, where am I wrong?
My version is nanocad 11 plus. Thank you
I have a problem with the fillet command. Very often it doesn't work because "lines are not complanar". But if I see on the properties, both are on the same level. I also never draw in other plan than 2d. So, where am I wrong?
My version is nanocad 11 plus. Thank you
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
#2
Posted 14 February 2020 - 02:34 PM
Hi.
Could you attach an example?
Could you attach an example?
#3
Posted 17 February 2020 - 09:40 AM
Hi Kreator,
yes thank you. Here you can find the two screenshots.
I don't know why, but properties panel refuses to open
yes thank you. Here you can find the two screenshots.
I don't know why, but properties panel refuses to open
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
#4
Posted 17 February 2020 - 09:43 AM
What about the drawing itself, not just screenshots?
#5
Posted 17 February 2020 - 10:04 AM
do you prefer the attachment?
Here you can find it:
https://www.dropbox....ilievo.dwg?dl=0
thank you for your support!
Here you can find it:
https://www.dropbox....ilievo.dwg?dl=0
thank you for your support!
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
#6
Posted 17 February 2020 - 10:30 AM
Hello,
Object is in locked layer VL_Wall, .... no ?
Patrick
Object is in locked layer VL_Wall, .... no ?
Patrick
#7
Posted 17 February 2020 - 10:37 AM
The reason is that the plines are in defferent planes. If you choose them both and look at Level property in Property window you'll see, that it says Different, despite they are both 0 if selected separately. Settin 0 Level for both will solve the problem. Maybe 1 of them is 0.0000000000001, that is shown as 0.0000.
#8
Posted 17 February 2020 - 10:39 AM
Hi pguimber, thank you for your reply. The layer weren't locked, I uploaded fastly the file while I was working.
@Kreator, maybe your are right. How can I set for all of them the 0.0000 level?
Thank you so much!
@Kreator, maybe your are right. How can I set for all of them the 0.0000 level?
Thank you so much!
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
#9
Posted 17 February 2020 - 10:43 AM
Select both plines, RMB, Properties (or Ctrl+1) - you'll see properties window. Find Level there and set 0.
#10
Posted 17 February 2020 - 11:00 AM
thank you very much. You were wright, it works. Even if there is a 0 in the panel, maybe there is a tiny difference.
Thank you!
Thank you!
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
#11
Posted 17 February 2020 - 11:01 AM
In NanoCad V5.... no problem ! Z all at 0,00, fillet is correct !
#12
Posted 17 February 2020 - 11:05 AM
maybe 11 plus is more sensitive since v5 is only 2d? Don't know!
Anyway thank you too
Anyway thank you too
my websites:
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
one for my work as architect: http://www.virginialorello.it
and one container of tools for creatives: http://scatolabox.altervista.org/
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users